Die Struktur besteht aus einem I-Profil-Träger und zwei Rohrfachwerkträgern. The structure contains several imperfections and it is loaded by the force Fz. Das Eigengewicht wird in diesem Beispiel nicht berücksichtigt. Determine the deflections uy and uz and axial rotation φx at the endpoint (Point 4). Dieses Verifikationsbeispiel basiert auf dem von Gensichen und Lumpe vorgestellten Beispiel.
Dieses Verifikationsbeispiel basiert auf dem Verifikationsbeispiel 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
Das Verifikationsbeispiel beschreibt Windlasten aus mehreren Anströmrichtungen am Modell einer Gebäudegruppe. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
A long, thin beam is carrying a concentrated mass and is loaded by a time-dependent force. Er wird einfach gelagert. The problem is described using the following parameters. Determine the deflections in the given test times.
Stellen wir uns ein biegesteifes Gerüstrohr vor, das durch einen Knotenlager für Gerüst unten befestigt und sowohl durch ein Moment als auch durch eine Kraft belastet wird. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Ein Stahlträger mit quadratischem Querschnitt wird mit einer Normalkraft und einer verteilten Belastung beansprucht. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
A single mass system is subjected to loading force. Bestimmen Sie die Durchbiegung des Systems.
Es soll die maximalen Durchbiegungen des Blockes unter Berücksichtigung bzw. Vernachlässigung der Schubwirkung ermittelt werden. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
In diesem Beispiel soll der nicht umkehrbare Prozess aufgezeigt werden, der durch Reibung verursacht wird. After the loading and unloading, the end-point is in a different position than where it was at the beginning. Determine the movement of the node in the X direction.
A two-layered, open-ended, thick-walled vessel is loaded by inner and outer pressure; therefore, there is no axial stress. Es wird die radiale Durchbiegung von Innen- und Außenradius sowie der Druck (radiale Spannung) ermittelt, wobei das Eigengewicht nicht berücksichtigt wird.
Weisen Sie nach, dass die Ergebnisse durch die Kopplung unterschiedlicher dimensionaler Elemente nicht beeinflusst werden. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
Vier Stützen sind unten fixiert und oben durch einen starren Block verbunden. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Eine aus einem I-Profil bestehende Struktur ist in Gabellager eingebettet. The axial rotation is restricted on both ends while warping is enabled. The structure is loaded by two transverse forces in the middle. The verification example is based on the example introduced by Gensichen and Lumpe.
Am oberen Ende ist ein Stab mit quadratischem Querschnitt befestigt. The rod is loaded by self-weight. For comparison, the example is also modeled with the concentrated force load, the value of which is equal to the gravity. The aim of this verification example is to show the difference between these types of loading, although the total loading force is equal.
Es wird ein Kragträger mit einem I-Trägerquerschnitt der Länge L definiert. The beam has five mass points with masses m acting in the X-direction. The self-weight is neglected. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
A cable is loaded by means of a uniform load. Das hat eine deformierte Form in Gestalt von einem Kreissegment zur Folge. Determine the equilibrium force of the cable to obtain the given sag of the cable. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Berücksichtigen Sie die im Bild Nr.1 dargestellte Stabspannweite ASTM A992 W 18 × 50 und die gleichmäßigen Eigen- und Nutzlasten. The member is limited to a maximum nominal depth of 18 inches. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
Bestimmen Sie die maximale Durchbiegung von vier unten befestigten Stützen, die oben durch einen starren Block verbunden sind. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
Bestimmen Sie das Biegemoment, welches den Stab am freien Ende des Kragarms in eine kreisförmige Form biegt. Neglecting the beam's self-weight, assuming the large deformation analysis, and loading the cantilever with the moment, determine its maximum deflections.
Das Verifikationsbeispiel beschreibt die stationäre Strömung um ein Hochhaus, das zwischen Häuserblöcken steht (skaliertes Modell). Das Beispiel kommt aus dem Architectural Institute of Japan (AIJ). Die gewählten Ergebnisse (Geschwindigkeitsgröße) werden mit den Messwerten verglichen.
An beiden Enden ist ein dreidimensionaler Block aus elastisch-plastischem Material mit Verfestigung befestigt. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.
Das Architectural Institute of Japan (AIJ) hat eine Reihe an bekannten Benchmark-Szenarien für Windsimulation vorgestellt.
Der Nache Beitrag dreht sich dabei um den "Fall A - Hochhaus mit 2:1:1 Form".
Im Folgenden wird das beschriebene Szenario in RWIND2 nachgebildet und die Ergebnisse mit den simulierten und experimentellen Ergebnissen des AIJvergleich.
Das Verifikationsbeispiel beschreibt die stationäre Umströmung an einem isolierten Gebäude (skaliertes Modell) am Beispiel von Architectural Institute of Japan (AIJ). The chosen results (velocity magnitude) are compared with the measured values.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. Die plastische Oberfläche wird nach der Tsai-Wu-Plastizitätstheorie beschrieben.
Eine Struktur besteht aus vier Fachwerkstäben, die in Gelenklagern eingebettet sind. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Das vorliegende Verifikationsbeispiel beschreibt Druckbelastungen an den Wänden von Gebäuden in Tandemanordnung, die sich in Bodennähe befinden. The buildings are simplified to rectangular objects and scaled down while maintaining the elevation ratios. The pressure distribution on the walls of the model of a medium-high building was conducted by an experiment. The chosen results (pressure coefficient Cp) are compared with the measured values.
Eine symmetrische flache Struktur besteht aus acht gleichen Fachwerkstäben, die in Gelenklagern eingebettet sind. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. Die plastische Oberfläche wird nach der Tsai-Wu-Plastizitätstheorie beschrieben.
A closely coiled helical spring is loaded by a compression force. The spring has middle diameter D, wire diameter d, and it consists of i turns. Die Gesamtlänge der Feder ist L. Determine the total deflection of the spring for the member model and one‑turn deflection for the solid model.
A member with the given boundary conditions is loaded by torsional moment and axial force. Neglecting its self-weight, determine the beam's maximum torsional deformation as well as its inner torsional moment, defined as the sum of a primary torsional moment and torsional moment caused by the normal force. Vergleichen Sie diese Werte, während Sie den Einfluss der Normalkraft annehmen oder nicht berücksichtigen. The verification example is based on the example introduced by Gensichen and Lumpe.