Registrieren Sie sich für das Dlubal-Extranet, um die Software optimal nutzen zu lassen und ausschließlichen Zugriff auf Ihre persönlichen Daten zu haben.
Das Architectural Institute of Japan (AIJ) hat eine Reihe an bekannten Benchmark-Szenarien für Windsimulation vorgestellt. Der Nache Beitrag dreht sich dabei um den "Fall A - Hochhaus mit 2:1:1 Form". Im Folgenden wird das beschriebene Szenario in RWIND2 nachgebildet und die Ergebnisse mit den simulierten und experimentellen Ergebnissen des AIJvergleich.
Das Architectural Institute of Japan (AIJ) hat eine Reihe an bekannten Benchmark-Szenarien für Windsimulation vorgestellt. Der Nachfolgende Beitrag dreht sich dabei um den "Case D - high-rise building among city blocks". Im Folgenden wird das beschriebene Szenario in RWIND2 nachgebildet und die Ergebnisse mit den simulierten und der experimentellen Resultate des AIJ verglichen.
Das Architectural Institute of Japan (AIJ) hat eine Reihe an bekannten Benchmark-Szenarien für Windsimulation vorgestellt. Der Nachfolgende Beitrag dreht sich dabei um den "Case E - a building complex in an actual urban area with dense concentration of low-rise buildings in Niigata City". Im Folgenden wird das beschriebene Szenario in RWIND2 nachgebildet und die Ergebnisse mit den simulierten und der experimentellen Resultate des AIJ verglichen.
Eine einfach gelagerte Rechteckplatte wird unterschiedlichen Lastarten ausgesetzt. Assuming only the small deformation theory and neglecting self-weight, determine the deflection at its centroid for each load type.
Vier Stützen sind unten fixiert und oben durch einen starren Block verbunden. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Berücksichtigen Sie die im Bild Nr.1 dargestellte Stabspannweite ASTM A992 W 18 × 50 und die gleichmäßigen Eigen- und Nutzlasten. The member is limited to a maximum nominal depth of 18 inches. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
Eine Stahlbetonstütze wird für den GZT bei Normaltemperatur gemäß DIN EN 1992-1-1/NA/A1:2015 auf Grundlage von 1990-1-1/NA/A1:2012-08 bemessen. Für den Nachweis wird das Verfahren mit Nennkrümmung verwendet; siehe DIN EN 1992-1-1, Abschnitt 5.8.8. Die fragliche Stütze befindet sich am Rand eines dreifeldrigen Rahmentragwerks, das aus 4 auskragenden Stützen sowie 3 einzelnen Trägern, die daran gelenkig angeschlossenen sind, besteht. Die Stütze wird durch die Vertikalkraft des Fertigteilträgers sowie durch Schnee und Wind beansprucht. Die Ergebnisse werden mit der entsprechenden Fachliteratur verglichen.
A cantilever is loaded by a transversal and an axial force on the right end and is fully fixed on the left end. Das Problem wird durch folgenden Parametersatz beschrieben. The problem is solved by using the geometrically linear analysis, second-order analysis, and large deformation analysis.
Das Ziel des vorliegenden Verifikationsbeispiels ist es, die Fluidströmung um das Segelflugzeug zu analysieren. Die Aufgabe besteht darin, den Strömungswiderstandskoeffizienten und den Auftriebsbeiwert mit Bezug auf den Anstellwinkel zu bestimmen. Diese Beiwerte können auch als Kurve in das Polardiagramm eingezeichnet werden. Aus dem Geschwindigkeitsfeld kann auch der Grenzwinkel für eine laminare Fluidströmung um das Flügelprofil bestimmt werden. In RWIND 2 wird das vorhandene 3D-CAD-Modell (STL-Datei) verwendet.
A thin rectangular orthotropic plate is simply supported and loaded by uniformly distributed pressure. The directions of axes x and y coincide with the principal directions. Bestimmen Sie maximale Durchbiegung der Platte, ohne das Eigengewicht dabei zu berücksichtigen.
Eine Struktur besteht aus zwei Fachwerkträgern, die in die Gelenklager eingebettet sind. The structure is loaded by concentrated force. The self-weight is neglected. Determine the relationship between the loading force and the deflection, considering large deformations.
Eine symmetrische flache Struktur besteht aus acht gleichen Fachwerkstäben, die in Gelenklagern eingebettet sind. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
Eine Struktur besteht aus vier Fachwerkstäben, die in Gelenklagern eingebettet sind. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Dieses Beispiel dient zur Veranschaulichung der Ebene. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.
Bestimmen Sie die maximale Durchbiegung von vier unten befestigten Stützen, die oben durch einen starren Block verbunden sind. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
An beiden Enden ist ein dreidimensionaler Block aus elastisch-plastischem Material mit Verfestigung befestigt. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.
A member with the given boundary conditions is loaded by torsional moment and axial force. Neglecting its self-weight, determine the beam's maximum torsional deformation as well as its inner torsional moment, defined as the sum of a primary torsional moment and torsional moment caused by the normal force. Vergleichen Sie diese Werte, während Sie den Einfluss der Normalkraft annehmen oder nicht berücksichtigen. The verification example is based on the example introduced by Gensichen and Lumpe.
A long, thin beam is carrying a concentrated mass and is loaded by a time-dependent force. Er wird einfach gelagert. The problem is described using the following parameters. Determine the deflections in the given test times.
Es wird ein Kragträger mit einem I-Trägerquerschnitt der Länge L definiert. The beam has five mass points with masses m acting in the X-direction. The self-weight is neglected. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Ein gekrümmter Träger besteht aus zwei Trägern mit rechteckigem Querschnitt. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
Weisen Sie nach, dass die Ergebnisse durch die Kopplung unterschiedlicher dimensionaler Elemente nicht beeinflusst werden. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. Die plastische Oberfläche wird nach der Tsai-Wu-Plastizitätstheorie beschrieben.
Am oberen Ende ist ein Stab mit quadratischem Querschnitt befestigt. The rod is loaded by self-weight. For comparison, the example is also modeled with the concentrated force load, the value of which is equal to the gravity. The aim of this verification example is to show the difference between these types of loading, although the total loading force is equal.
A cable is loaded by means of a uniform load. Das hat eine deformierte Form in Gestalt von einem Kreissegment zur Folge. Determine the equilibrium force of the cable to obtain the given sag of the cable. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Das Verifikationsbeispiel beschreibt die stationäre Strömung um ein Hochhaus, das zwischen Häuserblöcken steht (skaliertes Modell). Das Beispiel kommt aus dem Architectural Institute of Japan (AIJ). Die gewählten Ergebnisse (Geschwindigkeitsgröße) werden mit den Messwerten verglichen.
Stellen wir uns ein biegesteifes Gerüstrohr vor, das durch einen Knotenlager für Gerüst unten befestigt und sowohl durch ein Moment als auch durch eine Kraft belastet wird. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
A cantilever is loaded by a moment at its free end. Using the geometrically linear analysis and large deformation analysis, and neglecting the beam's self-weight, determine the maximum deflections at the free end. Dieses Verifikationsbeispiel basiert auf dem von Gensichen und Lumpe vorgestellten Beispiel.
Bestimmen Sie das Biegemoment, welches den Stab am freien Ende des Kragarms in eine kreisförmige Form biegt. Neglecting the beam's self-weight, assuming the large deformation analysis, and loading the cantilever with the moment, determine its maximum deflections.
A simply supported beam is loaded by pure bending. Aufgrund des Biegeknickens versuchen Sie die Verzweigungslast und den zugehörigen Lastfaktor zu ermitteln.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. Die plastische Oberfläche wird nach der Tsai-Wu-Plastizitätstheorie beschrieben.