Accessing Global Settings
Basic settings for the concrete design are managed in the 'Global settings' dialog box. This dialog box is essentially independent of the standard that you have selected in the model base data. However, the default values may differ from each other.
You can access the global settings using one of the following options:
- Shortcut menu in the 'Concrete Design' navigator entry
- Button
in the toolbar of the tables for concrete design
Global Settings
Configurations to Be Analyzed
Using the check boxes, you can control which design configurations are generally to be analyzed. When designing according to EN 1992-1-1, the configurations for the 'ultimate limit state' and the 'serviceability limit state' are activated by default.
Design Method
The 'enumeration method' is preset for both members and surfaces. The 'enveloping method' and the 'mixed method' are available as further design methods in the list.
- Enumeration method: All load combinations within a design situation are calculated one by one. This generally leads to the most accurate results, but may result in increased calculation times.
- Enveloping method: First, the envelope internal forces resulting from the extreme values for the design situation are calculated. The envelope is then used for the design. This usually results in a shorter calculation time, but may lead to an uneconomical design compared to the enumeration method.
- Mixed method: The two methods described above are combined. Here, you have the option of adjusting the 'number of variants' as a limit value at which the switch between the enumeration method and the enveloping method takes place. With the default value of 20, the program uses the enumeration method as long as the number of "result variants" is less than 20. If the number of variants within a design situation is greater than or equal to 20, the enveloping method is applied in order to save calculation time. You can make the settings separately for members and surfaces.
Optimization - Maximum Permissible Utilization (in Preparation)
The design concept is based on a design method. This means that you specify the cross-section and the reinforcement, and the program performs the design checks based on these specifications. The optimization of cross-sections and reinforcement specifications is also planned for the future development of RFEM and RSTAB. A specific design criterion or a design ratio is targeted for the individual design checks. You can also specify a value different from '1.00', which may be smaller or larger, in order to influence the optimization objective.
Saving Results
You can specify whether, for members, the results are to be saved for the individual x-locations of the member ('By location') or only for the member as a whole ('By object'). The latter requires less time, but makes a detailed evaluation in the result tables more difficult.
For surfaces, you can specify whether the results are to be saved for each FE mesh node or grid point and each design check ('By location') or whether, for each design check, only the result of the governing location in the surface is to be saved ('By object').
Smoothing Settings for Result Beam Calculation
A result beam integrates the internal forces of members, surfaces, or solids. For the design in the add-on, you can control which smoothing setting is applied when integrating the results. The following options are available in the list:
- Constant in finite elements
- Non-continuous
- Continuous within surfaces/solids (default setting)
- Continuous within surface sets/solid sets, otherwise within surfaces/solids
- Continuous within all surfaces/solids
The individual options are described in the chapter result smoothing of the RFEM manual.
Showing Results
The check box controls whether the design results are prepared for each design situation. It is deactivated by default so that work in the result tables can be carried out without long waiting times.
Calculating Results
Using this option, you can control whether the locations of the FE mesh nodes or the grid points are to be used for the design of surfaces (see the chapter results per surface of the RFEM manual).
The two options of the list affect the results in the tables and in the design check details: They allow you to control whether the values of the mesh nodes or of the grid points are output. The grid of the surfaces represents an output independent of the FE mesh at result points with regular spacing (see the chapter surfaces of the RFEM manual). These options have no influence on the graphical results.
Interaction Diagram
Here, you can define the parameters to be used for the result display of the design check details as an interaction diagram.
Reinforcement Bar
In the Reinforcement bar category, under Standard list of possible diameters, you define which bar diameters the program may use for the automatic design of the diameter. The list is defined separately for:
- Diameters for stirrup reinforcement ds,st,p
- Diameters for longitudinal reinforcement ds,p
Enter the diameters separated by commas, for example '10.0, 16.0, 20.0'.
The standard lists apply to the entire model. They are transferred as a specification in the Additional parameters dialog box of the reinforcement groups.
Lifecycle of Results
The results of the concrete design are deleted as soon as you make a modification to the input data. This ensures that the design is based on the correct boundary conditions. However, in some cases it may be useful to retain the results, for example if you want to adjust the provided reinforcement and still see the results of the previous calculation – the reinforcement that is not covered. In this case, deactivate the check box in order to avoid a complete recalculation of the concrete results.