12140x
000243
2023-12-08

Imperfection Cases

Imperfection cases describe the boundary conditions of the imperfections. This allows you to specify whether geometric imperfections or equivalent loads are to be taken into account. The specifications are regulated in the individual standards.

Base

The Base tab controls which type of imperfection is present. Imperfections can be taken into account, for example, in the form of equivalent loads, geometric pre-deformations, or story-by-story inclinations.

In the Assignment tab, you can assign the imperfection case to specific load cases and combinations.

Settings

Various imperfection types are available for selection in the list.

Local Imperfections

The imperfections are modeled by equivalent loads. The initial sways and precambers depend on axial forces. You can define the imperfections in the Local Imperfections categories for members and member sets.

Equivalent Loads from Load Case

The imperfections are based on the loads of a specific load case. You can assign this load case in the Equivalent Loads from Load Case tab or create it anew.

Initial Sway Imperfection via Table

With this imperfection type, imperfections can be modeled story by story. Define the parameters in the Initial Sway Imperfection via Table tab.

Structural Deformation

The imperfections are based on the deformations of a load case or a load combination. Define the governing parameters in the Structural Deformation tab.

In the 'Source type' list, select whether the displacements are based on a load case or a load combination.

Buckling Mode

Important

This imperfection type is available if the Structure Stability add-on (paid) is activated in the model base data.

The imperfections are based on the mode shapes of a stability analysis. You can define the governing parameters in the Buckling Mode tab.

In the 'Source type' list, select whether the displacements are based on a load case or a load combination. However, the governing imperfection shapes can also be determined automatically from the buckling modes for all assigned load cases and load combinations.

Dynamic Mode Shape

Important

This imperfection type is available if the Modal Analysis add-on (paid) is activated in the model base data.

The imperfections are based on the mode shapes of a dynamic analysis. You can define the governing parameters in the Dynamic Mode Shape tab. Only one option is available in the 'Source type' list, since the displacements in modal analyses can only be taken into account for load cases.

Group of Imperfection Cases

This imperfection type offers the possibility to combine the specifications from several imperfection cases. You can group the imperfection cases in the Group of Imperfection Cases tab and scale them with factors.

Options

The 'Consider for generated load combinations' check box is activated by default. This ensures that the imperfection case is taken into account for all load combinations that are not covered by a manual selection in the Assignment tab.

Example

In the 'Assignment' tab, the load case "Wind" is assigned manually. As a result, all load combinations that use this load case are also assigned automatically. For load combinations without wind, however, the imperfection case is only taken into account if the option 'Assign to all load combinations without assigned imperfection case' is activated.

Tip

The active check box guarantees that the imperfection case is taken into account for all load combinations.

Equivalent Loads from Load Case

The equivalent loads are available as an imperfection type (see image Selecting imperfection type).

You can describe the imperfections in a load case by equivalent loads. Assign the None load case category to this load case so that it is not taken into account in the combinatorics, but only as an imperfection load case. In this way, you can define stabilization loads independently of axial forces, for example – in contrast to inclinations or "notional loads" which act as equivalent loads in relation to axial forces.

Select the load case in the list or create a new load case using the New button.

Info

Only load cases of the 'None' category are displayed in the list.

Initial Sway Imperfection via Table

The initial sway imperfection is available as an imperfection type (see image Selecting imperfection type).

Story imperfections

You can describe the normative displacement of a building in a table. This means you do not have to define imperfections for each individual column. The story areas of the table control how the nodes in the building sections are displaced.

Define the ordinates of the stories and assign the inclinations. You can add rows using the New button. Make sure that the ordinates are in ascending order. From the specifications, RFEM determines a geometric displacement and applies it to the FE nodes.

Options

If the imperfections are not to be referenced to the global XYZ coordinate system, you can select or create a user-defined 'coordinate system'. The 'story direction' specifies the ordinate of the stories; this also makes vertically oriented initial sway imperfections possible.

The 'imperfection direction' defines the direction(s) in which inclinations are applied. With the default setting 'XY', the inclinations for the X and Y directions are to be specified in the table. If they act in one direction only, define the corresponding axis in the list.

In the table, the 'inclination factor as reciprocal of 1' is displayed. If you deactivate the check box, the values appear as decimal numbers.

Structural Deformation

The structural deformation is available as an imperfection type (see image Selecting imperfection type).

The 'imperfection shape' is based on the deformations of a load case or a load combination. The geometric pre-deformations are scaled to a sag.

Imperfection shape from

Select the governing load case or load combination in the list. Using the New button, you can create a new load case or load combination.

Imperfection sag

The 'reference location' defines the location in the model whose displacement serves as the reference for the sag. Usually, this is the location with the greatest displacement. However, you can also select another node in the list or define it graphically using the Single Selection button.

If the imperfections are not to be referenced to the global XYZ coordinate system, you can select or create a user-defined 'coordinate system'. The 'scaling direction' defines the orientation of the imperfections. With the options 'S' and '-S', spatially pronounced imperfections are possible, such as those occurring in shell models, for example.

Specify the 'imperfection sag' which represents the maximum geometric displacement. The displacements of the FE nodes are scaled to this value. The deformation shape of the load case or load combination specified above forms the basis.

Info

If you use free loads, they are applied to the deformed model. In this case, part of the load may lie outside the defined effective area and not be taken into account.

Buckling Mode

The parameters of the buckling mode imperfection type can be defined if the critical load is calculated for a load case or a load combination using the Structure Stability add-on. The concept of the tab is matched to the source type.

Buckling mode from load case/load combination

The 'imperfection shape' is based on the eigenvalues of a load case or a load combination. The mode shapes are scaled to a sag.

Imperfection shape from

Select the governing load case or load combination in the list. Using the New button, you can create a new load case or load combination. Then define the buckling mode in the list on which the imperfections are to be based.

Important

Some imperfections can only be created on the basis of manually defined load combinations: Automatically generated combinations can change quickly when input parameters are modified. As a result, a load combination assigned here would no longer be valid.

Imperfection sag

The reference location defines the location in the model whose displacement serves as the reference for the sag. Usually, this is the location with the greatest displacement. However, you can also select another node in the list or define it graphically using the Single Selection button.

If the imperfections are not to be referenced to the global XYZ coordinate system, you can select or create a user-defined coordinate system. The scaling direction defines the orientation of the imperfections. With the options 'S' and '-S', spatially pronounced imperfections are possible, such as those occurring in shell models, for example (see image Selecting scaling direction).

Specify the imperfection sag which represents the maximum geometric displacement. The displacements of the FE nodes are scaled to this value. The mode shapes of the load case or load combination specified above form the basis.

Automatic imperfections

When determining the imperfections automatically, the imperfection shape is derived from the respective load-dependent mode shape of the model and scaled with the defined imperfection amplitude.

Settings for automatic determination

Define the number of shapes to be analyzed. Note the following: For each load case and each load combination, so-called "sub-load cases" or "sub-load combinations" are created in which the imperfection shape is taken into account. Two sub-load cases or sub-combinations are created per mode shape, since each mode shape is scaled once in the positive and once in the negative direction. These sub-load cases and sub-combinations can then be analyzed like normal load cases or load combinations.

Example: You have assigned automatic imperfections to LC1 and specified two shapes to be analyzed. As a result, the sub-load combinations LC1.1 to LC1.4 are created – that is, four sub-load combinations.

The definition type allows you to control the input for scaling the mode shapes. Currently, two options are available in the list:

Info

The maximum amplitude of the mode shape from the stability analysis is always scaled to a dimensionless value of 1.0. This scaling must be adjusted to the corresponding imperfection sag.

  • EN 1993-1-1: The imperfection sag is determined according to the normative specifications per EN 1993-1-1 Tab. 5.1. In the further sections, you can adjust the imperfection parameters.

Parameters

Specify whether the cross-section design is to be 'elastic' or 'plastic'. The imperfection sags to be used depend on this decision.

Precamber for

The buckling curve of the cross-sections is generally known. For 'members without buckling curve' (with unknown buckling curve), you can specify the value manually. The same applies to 'surfaces and solids' which do not have a buckling curve according to EN 1993-1-1.

Info

For models consisting of several objects, a weighted interpolation of the imperfection sag is performed: In addition to the member with the maximum amplitude, all objects in the system are taken into account. Depending on the destabilizing energy that each object contributes within the mode shape, its imperfection sag is weighted. The weighted average of all imperfection sags within the system then results in the final imperfection amplitude.

Dynamic Mode Shape

The parameters of the dynamic mode shape imperfection type can be defined if a modal analysis is performed for a load case or a load combination.

The 'imperfection shape' is based on the dynamic eigenvalues of a load case or a load combination. The mode shapes are scaled to a sag.

Imperfection shape from

Select the governing load case or load combination in the list. Using the New button, you can create a new load case or load combination. Then define the mode shape in the list on which the imperfections are to be based. With the 'Automatic' option, you can have the program determine the governing mode shape.

Imperfection sag

You can define the parameters as described in the Imperfection sag section for a buckling mode.

Group of Imperfection Cases

The group of imperfection cases is available as an imperfection type (see image Selecting imperfection type).

You can combine several imperfection cases in a group and, for example, take them into account simultaneously. This option is often useful for shell buckling in order to apply global imperfections and local buckling.

Define the imperfection cases that are to be combined. You can add rows in the table using the New button.

You can apply a 'factor' to each imperfection case. Using the 'operator', specify whether the imperfection cases act simultaneously ('and') or whether they mutually exclude each other ('or').

Assignment

In the Assignment tab, you can assign one or more load cases or load combinations to the imperfection case. Only then is the imperfection case taken into account in the calculation.

Assign

All load cases that you have created are listed in the 'Assign' column. To transfer a load case to the 'Assigned objects' list, you can use the following options:

  • Double-click the load case.
  • Select the load case. Then click the Add button.

Assigned objects

The 'Assigned objects' column manages all load cases that you assign to the imperfection case. For example, if the imperfection case 'Wind in +X' is to be taken into account with the load case 'Wind in +X', transfer this load case to the list as described above. If the combination wizard is active, all load combinations that use this load case are also assigned.

Info

If you have checked the option Assign to all load combinations without assigned imperfection case in the 'Base' tab, the list also includes load combinations that are not assigned elsewhere.

In this way, you can match imperfection cases with the effective directions of load cases: For example, an imperfection case with inclinations in X acts for wind load in X, and an imperfection case in Y acts for wind load in Y. For unassigned load combinations (those without wind loads), each imperfection case is taken into account separately. RFEM creates two load combinations each with identical superposition criteria but different imperfection cases.

Parent Chapter